Raised-panel steel
Carriage house
Modern flush
Full-view glass
LiftMaster openers
Chamberlain openersFull 25-point door and opener safety check with every visit - springs, cables, rollers, tracks, and your LiftMaster or Chamberlain opener included
You get a price before we start. It does not change when the pro arrives.
Get your free estimateStyles & brands we work with
- Raised-panel steel
- Carriage house
- Modern flush
- Full-view glass
- LiftMaster openers
- Chamberlain openers
See the difference
Before
After
Before
After
Before
AfterHow Much Does Spring Replacement Cost in Raleigh?
Spring replacement in Raleigh typically costs $180-$340 for a single torsion spring, including the spring and the labor to install it. Most Raleigh doors carry two springs, and since a matched pair is almost always replaced together to keep the door balanced, a pair usually runs about twice that: $360-$680. The written estimate we give you on site is the price you pay, and that estimate is free.
The number you land on depends on the spring type, the door’s weight, and how the job is set up. We work on the brands most Raleigh homes already have, including LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor, so the diagnosis fits the system in front of us rather than a generic guess.
Key Takeaways
- Single torsion spring replacement: $180-$340 in Raleigh.
- Matched pair (the usual case): about double, or $360-$680.
- Extension springs on a lighter door can sit lower in the range; heavy custom doors can push higher.
- Same-day spring work is often possible. Call (866) 942-6232 for a free estimate.
Spring Replacement Cost Breakdown (2026)
Here’s how the line items stack up for spring work in Raleigh this year. These are typical estimated ranges for common residential doors. Your written estimate sets the final price.
| Job | Typical estimated range (Raleigh, 2026) |
|---|---|
| Single torsion spring replacement | $180-$340 |
| Matched pair of torsion springs | $360-$680 |
| Spring repair (re-seat, re-wind, or replace a broken spring) | $180-$340 |
| Cable repair (often done alongside a spring swap) | $130-$250 |
| Roller replacement (smoother travel after a spring job) | $110-$220 |
| Track realignment (bent track from a snapped spring) | $120-$240 |
| Opener repair (if the opener was strained by a dead door) | $120-$320 |
What pushes a spring job toward the top of the range: heavier doors, high-lift or unusual track setups, springs that are rusted in place, or a broken spring that has also bent a track or snapped a cable. What keeps it near the bottom: a standard single-car door with one manageable spring and no collateral damage. We diagnose the whole door, not just the spring, so you know up front whether a cable or roller needs attention too. Repair or replace, we’ll tell you which one actually makes sense.
What Affects Spring Replacement Pricing in Raleigh
Two doors can carry the same spring and still cost different amounts to fix. These are the factors we weigh on every Raleigh spring job.
- Spring type and size. Torsion springs (the horizontal bar above the door) and extension springs (the ones running along the sides) price differently, and heavier doors need heavier springs. A two-car door with high-cycle springs will sit higher than a single-car door with standard springs.
- How many springs. Most Raleigh doors carry two torsion springs. Because they should be replaced as a matched pair, that’s the most common reason a bill lands near twice the single-spring figure.
- Door weight and material. A steel Clopay or Amarr door weighs more than a light aluminum frame, and the spring has to match. A heavier door means a bigger spring and more careful balancing labor.
- Condition of cables, rollers, and track. Raleigh’s humid summers and the occasional ice storm put wear on steel parts. If a snapped spring has kinked a cable or knocked a track out of line, that’s added to the job at its own line-item price.
- Whether the opener was strained. A door sitting dead for days can wear the opener’s gears. If the opener needs attention, opener repair runs $120-$320.
- Access and clearance. Tight garages, low headroom, or a door that shares space with stored items can slow the work and shift the estimate up a bit.
How to Save on Spring Replacement
Spring work is one of those jobs where the best savings come from not making things worse before we arrive. A few practical moves:
- Don’t run the opener on a door with a broken spring. It’ll strain the motor and can turn a spring job into a spring-plus-opener job. Leave the door down and call.
- Replace the pair, not just the broken one. The second spring is the same age and under the same load. Swapping both at once usually costs less over time than two separate single-spring visits.
- Bundle a tune-up with the spring swap. If the rollers and cables are already worn, replacing them during the same visit is cheaper than a second trip. Rollers run $110-$220; cable repair is $130-$250.
- Get the estimate before anyone touches the door. We give free written estimates. Call (866) 942-6232 and we’ll price the job so there are no surprises.
- Ask what’s driving the number. A good estimate explains why a job lands where it does. We’ll walk you through the spring size, the door weight, and any added line items.
Is It Cheaper to Repair a Spring or Replace It?
Repairing a spring almost always makes sense if the spring itself is intact, and that’s most of what we see in Raleigh. A spring that has slipped off its anchor, lost tension, or come unseated can often be re-seated and re-tensioned, and that’s covered by the $180-$340 repair range. A spring that has physically snapped, or one that’s heavily rusted and pitted, is a replacement, and it prices in the same range because the labor is similar. What we don’t recommend is trying to stretch a spring’s life past the point where it’s failing. A tired spring puts uneven load on cables and the opener, and that’s where the bigger bills come from. If the door is old and the springs, cables, and rollers are all near the end, we’ll tell you honestly whether repair or a new door install makes more sense. New door installation runs $700-$2200.
What Does a Snapped Spring Look Like, and Why Can’t I Fix It Myself?
A snapped torsion spring usually shows a clean gap in the coil, and the door goes heavy and won’t lift or won’t stay down. A snapped extension spring is visible as a stretched or broken spring along the side track, and the door may sag on one side. Here’s the part that matters: torsion springs are under extreme tension even after they break, and the winding bars and technique needed to release and reset that tension are a genuine injury risk to anyone without training. We don’t recommend DIY work on springs, cables, or the opener. A trained technician carries the right bars, the right spring size, and the know-how to keep the door from coming down hard. Our technicians have up to experience, and spring work is one of the most common calls we handle across the eight brands we service.
How Long Does a Spring Replacement Take in Raleigh?
A single-spring replacement usually takes 45 minutes to an hour and a half on a standard residential door; a matched pair with a cable or roller swap can run two to three hours. If the track is bent or the opener needs attention, add time. Most Raleigh spring jobs are done same-day when you call before the afternoon. Call (866) 942-6232 for a free estimate. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday.
Do You Work on My Brand of Door and Opener?
Very likely, yes. We service eight of the most widely installed garage door and opener brands in Raleigh homes: LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor. That matters for spring work because the spring size, the drum and cable setup, and the opener’s travel limits all vary by system. Being brand-agnostic means we recommend the spring your door actually needs, not the one a single manufacturer partnership pushes. Your opener is the brain of the system, and a strained opener from a broken spring gets the same careful diagnosis as the spring itself. One call covers the spring, the cables, and the opener. We’re Orchard Garage Door Repair, and you can see our full range of service on the main page.
FAQs – Spring Replacement Cost
How much does it cost to replace a garage door spring in Raleigh?
Spring replacement in Raleigh typically costs $180-$340 for a single spring. Because most doors carry two springs and they’re replaced as a matched pair, the usual total lands around $360-$680. The written estimate sets the final price, and estimates are free: call (866) 942-6232.
Can you replace just one spring, or do I need both?
You can replace just one spring, and it costs the single-spring range of $180-$340. But if both springs went in at the same time and have seen the same use, we usually recommend the pair, since replacing both at once costs about twice the single range and avoids a second service visit when the other one fails. We’ll price both options so you can decide: call (866) 942-6232.
Is spring replacement covered by homeowners insurance?
Usually not. Most policies treat a worn or broken spring as normal wear and tear, not a covered peril, so spring replacement is typically paid out of pocket at the $180-$340 single-spring range. If a storm or impact caused the damage, check your policy wording. For a clear estimate either way, call (866) 942-6232.
How much does garage door repair cost in Raleigh if the spring broke a cable too?
Spring plus cable is the most common combo we see. Spring repair runs $180-$340 and cable repair adds $130-$250, so the combined job typically lands around $310-$590, depending on the door. The written estimate sets the final number: call (866) 942-6232 for a free quote.
Can you come today for a broken spring?
Often, yes. Spring work is a common same-day job in Raleigh when you call before the afternoon. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday. Call (866) 942-6232 and we’ll book the earliest opening.
What does a full garage door replacement cost if the springs are shot?
If the door, springs, cables, and rollers are all near the end, a new door is worth pricing. New door installation in Raleigh typically runs $700-$2200, depending on size, material, and insulation. We’ll compare repair versus replace honestly: call (866) 942-6232.
Why Call Orchard for Spring Work in Raleigh
Springs are the part of the door that carries the most load and fails most often, so it pays to have the job diagnosed correctly the first time. We handle garage door repair, garage door opener repair, and full installation under one name, which means a strained opener or a bent track gets sorted out in the same visit as the spring. Our technicians have up to experience across LiftMaster, Chamberlain, Genie, Clopay, Amarr, Wayne Dalton, Craftsman, and Raynor systems. If you’re in the Raleigh area and your door has gone heavy or won’t lift, don’t force it. Call (866) 942-6232. We answer 24/7, with fast dispatch from 7am to 7pm, Sunday through Friday, and estimates are free.
Contact Us for a Free Spring Estimate
Ready to know exactly what your spring job will cost? Call (866) 942-6232 for a free estimate. We’ll diagnose the door, explain what needs attention, and give you a written price in the $180-$340 single-spring range or the matched-pair figure, whichever fits your door. Orchard Garage Door Repair covers spring replacement, opener repair, cables, rollers, tracks, and new door installation across Raleigh. Repair or replace, we’ll tell you which one actually makes sense, and the estimate is free.
Pricing reflects the Raleigh market as of 2026. Orchard Garage Door Repair offers free estimates – call (866) 942-6232.
What Our Customers Say
"The old chain drive sounded like a freight train through the bedroom above the garage. Went with the belt drive they recommended and now I genuinely cannot hear it open from upstairs."
- Yolanda Robinson"Replaced the bottom panel after I backed into it. Color match is close enough that you have to know to look for it."
- Terrence Carter"Door installed in about four hours, old one hauled away, and he stayed to program both cars and the wall panel before he left."
- Paige Doyle